Did you know?

Litter-Robot 4 features an easy-to-use control panel near the top of the unit. Power button. Press the Power button to turn the unit power ON or OFF.When turning the unit ON, the light bar will flash white, then the unit will perform a Clean cycle with a sequential round robin yellow light bar indicating the direction of rotation.Fix 3: Power on the unit. If the blinking blue light is caused by a power failure, simply plug the unit back in and wait for it to power on. In the event of a power failure, the Litter Robot will automatically enter standby mode and the blue light will blink. To power on the unit, simply plug it back into a working electrical outlet and wait ...If they are fast flashing they're the pinch sensor, but there are other errors which can cause flashing yellow lights. Step 1 is making sure that it isn't touching anything, like the wall - if you've already taken the darn thing apart you probably already did that though. Step 2 is something we do regularly with our robot because this used to ...If YES, you are done. Re-position Globe and verify that it completes a clean cycle (in this case adjustment of the cat sensor was not needed). 5. Turn the Base upside down so you are facing the bottom surface. Find the round black adjustment foot and simply turn it Clockwise (2) full complete turns (720 degrees). 6.Reply. bitchassslutasswhore • 10 mo. ago. When I get the yellow flashing lights, I lift the globe, vacuum out the litter, reset it in the right position, then I unplug it from the back of the box. Before plugging it back in, I hold in the cycle button, plug in while holding the button in, release, and it works again. Might help you too.Submit support request. Select a category for your ticket. Select a sub-category for your ticket. Please describe your issue. Got questions or issues? Contact Litter-Robot Support today. We’re dedicated to ensuring a seamless experience for you & your pet.So woke up this morning with litter robot 4 offline. The big light is solid blue with the little light flashing blue. How do I reconnect it? I pressed the wifi button once, goes to solid light yellow, pressed it again and goes back to blinking blue. If I press the wifi for 3 seconds, goes to flashing yellow, but nothing happens on the app.Yes, I had this same issue. I took the top cover off, removed the glove, and vacuumed up all of the loose litter and dust that had made its way all over the place after about 1.5 years of use. Still was getting the over torque fault even though the litter was significantly below the max line. Emptied the globe completely.Phone and Chat support available Mon-Fri: 9AM-7PM EST and Sat: 9AM-5PM EST, or submit a ticket anytime. Visit for solutions if your Litter-Robot 4 has a red light bar with a partial white flashing globe. Get instant support and fixes today.If your unit has a flashing red light bar or the unit will not cycle, this indicates that the cat sensor has been triggered for more than 30 minutes. You will also receive a notification on your phone if you use the Whisker app. Successful: If your unit returned home and displays a blue light bar, you've been successful.Welcome to the Ender 3 community, a specialized subreddit for all users of the Ender 3 3D printer. Here, enthusiasts, hobbyists, and professionals gather to discuss, troubleshoot, and explore everything related to 3D printing with the Ender 3.My litter robot is stuck on flashing red (1 per second). I know it's to do with the cat sensor saying there is too much weight. How do I fix it. The robot is on flat surface, not over full and clean. I have continuous problems with the unit. It is only 2.5 years old and already have had to change the tray sensor three times. I have tried to re set it but the light continues and it just won ...Litter-Robot 3 Open Air Circuit Board. Replacement Circuit Board (Without Panel) for Litter-Robot Compatible with Litter-Robot 3 only. Price: USD 80If it cannot cycle after three attempts, the globe will return to the home position, and the control panel will flash yellow and red or blue and red lights. There are a few things you can do to troubleshoot a jammed Litter-Robot globe: 1. Turn off the unit and unplug it. 2. Remove the bonnet. 3. Remove the globe. 4.Litter-Robot 4: Red Light Bar Flashing (Cat Sensor Fault) Litter-Robot 4: Red Light Bar Momentary Flash (Control Panel Lockout Mode) Litter-Robot 4: Red Light Bar with Partial White Flashing (Globe Position) Litter-Robot 4: Red Ping-Pong Light Bar (Motion in Drawer)Just got my litter robot and I to am having thi21K subscribers in the litterrobot community. Communi Press the test button on the sensor to ensure that the red and green lights are working properly. If the sensors are properly aligned and there are no obstructions, the status light should stop blinking. ... Litter Robot Blinking Blue Light: Causes & Fixes; Kuhn Mower Parts Diagram & Details; Honda HRX217 Parts Diagram & Details; Litter-Robot 4 is equipped with OmniSens 8 Ways To Make Your Cat Litter Last Longer. Use Clumping Litter. Control the Odor. Place A Mat Underneath the Litter Box. Consider A Self-Cleaning Litter Box. Use A Slotted Scooper. Fill To The Top Of The Box. Clean Your Box Frequently. Watch Out for Humidity In The Winter. Status Indicator Lights. Solid Blue: Fee

Watch on. If Litter-Robot 3 globe becomes jammed or overloaded when rotating clockwise, the motor will stop and reverse for 5 seconds. The unit will start to cycle again after 15 seconds, to attempt to return to the Home position. If after three attempts, the unit is unable to cycle, the globe will return to the Home Position and the control ...21K subscribers in the litterrobot community. Community for all things Litter-Robot. Post your experiences, tips, tricks, and hacks.Objects are resting or pressing on the unit. The red blinking light indicates CATS (the cat sensor) is detecting excess weight for more than 2 minutes. To test your changes, power the unit off and then on. Allow the unit to complete the start‐up cycle and return Home with a solid blue light. Your unit is operating normal.Reply. bitchassslutasswhore • 10 mo. ago. When I get the yellow flashing lights, I lift the globe, vacuum out the litter, reset it in the right position, then I unplug it from the back of the box. Before plugging it back in, I hold in the cycle button, plug in while holding the button in, release, and it works again. Might help you too. Status Indicator Lights. Solid Blue: Feeder is in Automatic Feeding Mode. Solid Yellow: Hopper is low indicating less than 20% food remaining. Solid Red: Hopper is critically low indicating less than 5% food remaining. Flashing Red: Dispenser is jammed. Solid Purple: Food Bowl and Food Chute are full for 12+ hours (food has not been consumed)

Reply. bitchassslutasswhore • 10 mo. ago. When I get the yellow flashing lights, I lift the globe, vacuum out the litter, reset it in the right position, then I unplug it from the back of the box. Before plugging it back in, I hold in the cycle button, plug in while holding the button in, release, and it works again. Might help you too.After your Litter-Robot cycles, it should return to the Home position, displaying a blue light bar. Successful: If your Litter-Robot displays a blue light bar, you've been successful. Unsuccessful: If you are still seeing a flashing red light bar, please follow these troubleshooting steps.…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Get started by following the steps below. If possible, place Li. Possible cause: Litter-Robot 4: Light codes guide. Litter-Robot 4 control panel features 5 buttons .