Did you know?

Splitcoaststampers.com - the world's #1 papercrafting community. You're currently viewing Splitcoaststampers as a GUEST. We pride ourselves on being great hosts, but guests have limited access to some of our incredible artwork, our lively forums and other super cool features of the site! You can join our incredible papercrafting …3 days ago · Step 8. Place spinner into the cut out notch in the front of your card. Put the bottom in first and then gently lift the top piece into the top. The cardstock will fit between the "sandwich" part. Hold card front upright and make sure your spinner spins nicely when you tilt the cardstock from side to side.Step 1. Fold the cardstock for the inside of the card in half. Place the cardstock with the mountain side of the score line facing up on the paper cutter and cut two parallel lines over the score line with the paper cutter. Use an Xacto knife™ and ruler instead of the paper cutter. Here, the lines were cut 1" from the left-hand side of the ...For the base piece in Step 1 of the tutorial, add 1/4" to the width of your cards for the width. The length of this piece will be 2 times the height of your card plus 1 1/2". Score at card height plus 1/4" from each end. For 5" x 5" cards, the base is 5 1/4" wide and 11 1/2" long, scored at 5 1/4" from each end.A community site for rubber stamp art, paper craft and scrapbook artists.Note that in order for the card to fold completely flat, the pop-up supports can only be installed on opposite sections of the pinwheel card—either the first and third, or the second and fourth. To install the first pop-up support, orient it so that you have the long (L) panel to the LEFT of the short (S) panel.An online community for art stampers and scrapbookers. Your Turn. You've seen the tutorial, now you try it! We've got a section of the gallery set aside for Kirigami Christmas Tree.Try this technique, then upload your artwork to … · Embrace Clinic and Care Center Needs Thank You Cards. purpleflowers. 01-31-2024 03:34 PM. by purpleflowers. 5. 285. December 2023 Mission - Cards For A Cause. purpleflowers.Step 4. To create the flower pot shape, place the cardstock in the paper trimmer with the top 2” flap flipped up and the bottom flap folded behind. Line up the 2” score line with the cutting track and the 5 ½” fold line with the ½” mark on the trimmer. Place the cutting guide over the card and cut. Turn cardstock and repeat.Step 5. Line up the bottom of your card edge with 2 3/4" (or the top edge with 7/8") and cut from the top to the first score line. Line up the left score line with the cutter groove and cut from the top to where your paper is cut.Step 5. Center one penny behind the cut out square. Adhere a Stampin’ Dimensional to the penny through the square. Hint: Depending on the size of the image, the dimensional adhesive may need to be trimmed. Place second penny on top of Stampin’ Dimensional to form a penny sandwich. Note:When it comes to private jet travel, the cost of a jet card can be a major factor in deciding which service to use. Flexjet offers a variety of jet cards that can be tailored to fi...Step 5. Add a few glue dots on the right side of the back side of the first circle under the score line. Use the score lines as a guide and adhere a second cardstock circle to the first. Create a 90 degree angle with your score line as shown in the picture.Start with 5 1/2 x 8 1/2. Score @ 2 1/8, 4 1/4, and 6 Nov 14, 2011 · Most of the cards I ma Take the 3½" x 11" piece of card stock, and trim one of the short ends using the most outer channel of the Coluzzle™ circle template. Step 2 Trim card stock opposite the curved flap as shown to measure a total length of 10 3/8". Jul 17, 2019 · Step 1. Cut the main image cardstock pane Step 6. Cut patterned paper into layering panels for the card. These should be 1/4” smaller (each way) than each card half, measuring from the single center cut line. The panels here are each 2 1/2" x 4”. Cut across the panel to create a layering piece for the larger area on each side (2 1/2” x 1 7/8” here). Business credit cards with no personal guar

Aug 2, 2017 · Step 2. To make the opening, set the scored insert place on the paper trimmer with the 5 3/8” side at the top. Line up to the 1 1/2” mark and place the blade 2” down. Cut to the 5” score line. Repeat at the 3 …Oct 15, 2008 · Guy's Anniversary Card by cjbapp at Splitcoaststampers On The Fly Again by cjbapp at Splitcoaststampers _____ Cher No longer stamping...on to bigger things. 10-09-2008, 01:28 PM #19 ilinacrouse. Splitcoast Dirty Dozen Alumni Creative Crew SU Design Team Alumni . Join Date: May 2007. Location: Alpharetta, GA ...Butterfly Artist Trading Cards. by Layersofink. >posted 40 minutes ago. Happy Easter. by Jesuisjeune. >posted 47 minutes ago. SC415 Ready To Celebrate. by 123scrap. >posted …In the market for a new credit card? Now there are plenty of choices when it comes to the best credit cards for rewards, especially regarding cashback offerings. Credit card reward...

An online community for art stampers and scrapbookers. Your Turn. You've seen the tutorial, now you try it! We've got a section of the gallery set aside for Kirigami Christmas Tree.Try this technique, then upload your artwork to …Do you want to make your own personalized Christmas cards this year, but don’t know where to start? Well, worry no more! This article will show you how to customize your cards in s...Oct 27, 2021 · Note that in order for the card to fold completely flat, the pop-up supports can only be installed on opposite sections of the pinwheel card—either the first and third, or the second and fourth. To install the first pop-up support, orient it so that you have the long (L) panel to the LEFT of the short (S) panel. …

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Step 1. Take the Iris Pattern and apply some Rep. Possible cause: Ask questions or find answers about stamping. Get help with something that isn't workin.